Skip to main content

How to read a floor plan

What every line and number on a floor plan means. The complete beginner's guide.

7 min readUpdated 2026-11-02

A floor plan is a top-down view of a building, drawn as if the building has been sliced horizontally about 4 feet above the floor. Once you know what the conventions mean, you can read any plan.

Slicing at about 4 feet is why a plan shows windows as breaks in the wall (the cut passes through them), shows kitchen counters and furniture from above, and leaves out things higher up such as wall cabinets, beams and ceiling lights, unless they are drawn with dashed lines or symbols. Everything on a plan is drawn to scale: measure any line, multiply by the scale, and you get the real size.

This guide walks through a real plan, the Medium 2-Bedroom Apartment template in RoomSketch3D (30′ 6½″ × 26′ 6½″ outside): two bedrooms, a bath and an open kitchen/living room. Read in the order below — orientation, walls, openings, dimensions, labels, symbols — and any plan, from a builder's PDF to a real-estate flyer, makes sense.

In this guide

  1. 1

    Orientation

    North arrow somewhere on the plan — usually top-right or bottom-right corner. North up is conventional but not required. Read this first so you know which walls face which direction (matters for daylight, view, climate). In RoomSketch3D the small compass at the bottom right of the plan shows north (N in red); you can also drop a North Arrow symbol from the Symbols panel onto the plan so it prints on exports. See compass and beacons.

    The whole plan: Bedroom 2, Bath, Bedroom 1 and the Kitchen / Living room, each labelled with its size and area, dimensioned outside and inside.
  2. 2

    Walls

    Two parallel lines = a wall. The space between them = wall thickness. Thicker walls (often shaded or hatched) = exterior or load-bearing. Thinner walls = interior or non-load-bearing. Single line = sometimes a half-wall, railing, or partial wall. On this plan the outside walls are 6½″ thick and the interior walls 4½″ — typical for a wood-framed home (a 2×6 or 2×4 stud plus drywall). Wall thickness is why the outside dimension (30′ 6½″) is bigger than the room sizes inside it: the walls take up real floor. See wall thickness conventions.

    Thick outside wall on the left, thinner interior walls between rooms, two doorless openings into the bedrooms and the bath door's dashed swing arc.
  3. 3

    Doors

    Gap in the wall + quarter-circle arc = hinged door (the arc shows the swing). Gap in the wall + two short parallel lines = sliding door. Gap with the door drawn inside the wall = pocket door. Gap with no door shown = opening (no door). How to read a swing: the straight line is the door leaf drawn fully open; the arc is the path of its edge. The hinge is where the leaf meets the wall, and the door swings into the room the arc is drawn in. Leave the whole arc clear of furniture — a chair inside it stops the door opening. In the close-up above, the bath door is hinged on the right and swings into the bathroom; the two bedrooms have doorless openings. See door swing and hinge side.

  4. 4

    Windows

    Two parallel lines crossing the wall = window. Sometimes with an additional shorter line indicating sill or sash. RoomSketch3D draws a window as a light-blue pane set into the wall, divided into its sashes. Its width reads along the wall; its height and sill height (how high it starts off the floor) are not visible in plan view — look at an elevation for those (see floor plan vs blueprint vs elevation).

  5. 5

    Dimensions

    Lines with arrows at both ends and a number = a dimension. The number is the length of what the line spans. Typical dimensions shown: - Outer perimeter of each side - Interior room dimensions - Door and window positions on walls - Total dimensions of the building Read the chains: the line furthest out is the overall size, outside face to outside face (30′ 6½″ here). The line inside it is a chain of the rooms along that side (10′ 6½″ · 7′ 7½″ · 10′ 6½″): each number is the clear space between wall faces, so the chain plus the wall thicknesses adds up to the overall. Dimensions drawn inside a room are its clear width and length — the space you can actually furnish. Feet and inches are written 10′ 6½″ (10 feet 6½ inches).

    Overall (top), the room chain under it, and clear room sizes inside each room. Windows show as light-blue panes in the outside wall.
  6. 6

    Scale

    Scale notation somewhere on the plan: '¼" = 1'-0"' (quarter inch = one foot) is the most common residential scale. '1/8" = 1'-0"' for larger buildings. Means every quarter inch on the paper = 12 inches in real life. To measure, hold a ruler to the line; divide by 4 (or the relevant ratio). Many modern plans use a scale bar instead — a short ruler drawn on the sheet (0 · 1′ · 2′ · 3′). A scale bar stays right when a PDF is printed at a different size or zoomed on screen; a written scale is only true at the original paper size. RoomSketch3D's exports carry a scale bar, and the on-screen plan shows a live one at the top left that updates as you zoom.

    Bottom of an exported plan: the scale bar, then the overall size, gross area (to the outside faces) and usable area (inside the walls).
  7. 7

    Symbols

    Outlets, switches, lights, plumbing, HVAC — each has a standard symbol. See floor plan symbols for the full reference. A quick decoder for the common ones: a circle with two strokes on a wall is an outlet (letters beside it give the type, e.g. GFCI); an S is a switch (S₃ three-way); a circle with an X on the ceiling is a light; a dashed line from a switch to lights is a circuit.

    Electrical symbols read the same way on any plan: outlets on the walls, switches by the door, lights on the ceiling, dashed circuits between them.
  8. 8

    Furniture

    Drawn from above, to scale. - Sofa: rectangle with curved back. - Bed: rectangle with rounded headboard. - Dining table: round or rectangular shape with chair indicators. - Toilet: oval + small rectangle. - Sink: rectangle or oval. Because furniture is to scale, you can check clearances right on the plan: the gap between a bed and a dresser, the walkway past a sofa. A 36″ walkway and a door swing kept clear are the two checks that matter most.

  9. 9

    Room names and areas

    Each room labelled with name (e.g. 'BEDROOM', 'KITCHEN', 'LIVING') and often area (e.g. '12-0 × 14-0' or '168 sq ft'). On the plan above, Bedroom 1 reads 10′ 7″ × 12′ 7″, 133 sq ft: the clear width and length inside the walls and the floor area. Two totals are worth knowing: gross area is measured to the outside faces of the walls (the building's footprint — 811 sq ft here); usable area is the floor inside the walls (750 sq ft). Listings and builders may quote either, so check which one a number means before you compare two homes.

  10. 10

    Check it in 3D

    If a plan is hard to picture, look at it in 3D. Every RoomSketch3D plan opens in 3D with View in 3D; tick Dollhouse to cut away the front walls and see the rooms from above at an angle, the same layout the plan describes. See switch to 3d walkthrough.

    The same apartment in 3D: kitchen run and island at the front left, sofa and TV at the right, the two bedrooms and bath behind.

Tips

Start with the overall, then the rooms

Read the overall dimensions first to get the size of the whole place, then each room's clear size. If a room's numbers don't add up with its neighbours, a wall thickness is the usual difference.

Trace your path

Put a finger on the front door and walk through the plan: which way does each door swing, what do you see first, where would you drop your keys? It's the fastest way to understand a layout.

Check what the area means

811 sq ft gross and 750 sq ft usable are the same apartment. When comparing listings, make sure both use the same measure.

Common confusions

Measuring a printed PDF with a ruler

A PDF printed on letter paper instead of the original sheet size is no longer at ¼″ = 1′. Use the scale bar, or better, the written dimensions.

Forgetting wall thickness

Adding up room sizes gives less than the overall size because walls are 4–8″ thick each. Use the overall dimension for the footprint and the room dimensions for furniture.

Frequently asked questions

What does a circle with a line mean on a floor plan?

A circle with a line is often a door swing arc — the quarter-circle showing how a hinged door swings. Other circles can be outlets (with two slots) or lights (with X).

How do I know which way a floor plan faces?

Look for the north arrow — usually in a corner of the plan. It points to true north (or sometimes magnetic north).

What do the numbers like 10′ 6½″ mean?

Feet and inches: 10 feet 6½ inches. Some plans write it 10'-6 1/2". Metric plans give millimetres or metres and centimetres.

Why is the outside dimension bigger than the rooms added together?

Because the walls between and around the rooms have thickness. On the example plan the rooms along the top add to 28′ 8½″ while the overall is 30′ 6½″; the difference is two 6½″ outside walls and two 4½″ interior walls.

Are the room sizes measured inside or outside the walls?

Room sizes are the clear space inside the walls (wall face to wall face). Overall dimensions are to the outside faces.

Start designing your room

Draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android