Skip to main content

Door swing direction and hinge side

Two questions decide where a hinged door ends up when it's open: which side the hinges are on, and which way it swings. Get both right and the door parks against a wall instead of in the room.

5 min readUpdated 2026-11-16

Every hinged door comes with two decisions: which side the hinges are on (the door's hand), and which way it swings, into the room or out of it. They sound trivial; they aren't. Get them wrong and you reach for the handle on the wrong side every day, the open door covers the light switch, or it swings into the bed, and Smart Flow Check checks the wrong patch of floor.

Quick answer. Hinge the door on the side nearer the room's corner, so the open door lies flat against the wall. Swing it into the room it serves (bedrooms, bathrooms, closets, offices), unless that room is too small for the arc. Put the light switch on the handle side. For a house, the residential code doesn't tell you which way to swing a door; it only requires the main exit door to be a side-hinged door at least 32 in clear (IRC R311.2). The "swing in the direction of escape" rule is a commercial rule for rooms holding 50 or more people.

In this guide

  1. 1

    Hinge side (the 'hand' of the door)

    Stand on the side the door swings away from you (the side you push it open from). If the hinges are on your left, it's a left-hand door; on your right, a right-hand door. The handle is always on the opposite edge from the hinges. Door makers and suppliers use this to name a door (LH, RH, and for doors that swing toward you, LHR and RHR: 'reverse'). Prehung doors come already hung in one hand, so the hand on your plan is what you order.

  2. 2

    Swing direction (in vs out)

    Swing in means the door opens into the room you're entering. That's the norm for almost every interior door: bedrooms, bathrooms, closets, offices. The open door then sits inside the room, against its wall, and the hallway stays clear. Swing out means the door opens away from you, into the hall or outside. Reasons to do it: a powder room or closet too small for the arc (a 30 in door needs a 30 in quarter circle of clear floor), a bathroom where someone could fall against the inside of the door, or an exterior door in a windy, rainy spot where an outswing door seals better. Keep an outswinging door from hitting anyone in the hallway: the hall must be the door's width plus room to walk past.

    The same door four ways. In / Out picks the side it opens to; L / R picks the end the hinges are on.
  3. 3

    How to choose the hinge side

    Hinge on the corner side. Put the hinges on the edge nearer the room's corner (or the nearer wall that meets this one). When the door opens, it folds back flat against that wall and leaves the room open, and you walk straight in toward the room, not into the back of the door. Light switch on the latch side. The switch goes beside the handle edge, inside the room, about 48 in up, so your hand finds it as the door opens. If the hand is wrong, the open door hides the switch and you reach across the doorway in the dark. Check what the open door covers. A door folded back against a wall covers about its own width of that wall: no outlets, thermostats, shelving or artwork there, and allow for a door stop so the handle doesn't punch the drywall.

  4. 4

    What the codes say (and don't)

    Houses (IRC): the code doesn't set a swing direction for interior doors or for the front door. It requires at least one egress door per dwelling that is side-hinged, with a clear width of at least 32 in measured between the face of the door and the stop with the door open 90 degrees, and a clear height of at least 78 in (IRC R311.2). Landings at exterior doors must be at least as wide as the door and 36 in deep in the direction of travel (R311.3). Commercial and public buildings (IBC): doors must swing in the direction of egress travel where they serve a room or area with an occupant load of 50 or more (IBC 1010.1.2 in the 2015 to 2024 editions). That's where 'exit doors swing out' comes from; it isn't a house rule. Accessibility (ADA 2010 Standards): on the pull side of a door you approach head-on, leave 18 in of clear floor beside the latch and 60 in in front of the door (404.2.4). That's a minimum, not a comfort target, and it only applies where accessibility rules apply, but it's a good test for any door you want to be easy to use.

  5. 5

    In RoomSketch3D

    Tap any hinged door on the plan. Its settings (a floating card on a tablet or computer, a panel along the bottom on a phone) show: - In / Out: which side of the wall the door opens to. On an outside wall, In is into the house. On an inside wall the two buttons are simply the wall's two sides, so look at the plan: the dashed arc shows where the door goes. Tap the other button if it opens into the wrong room. Smart Flow Check tests the swing on exactly the side the arc is drawn, on an inside wall too, so with In / Out the wrong way round it checks the wrong room's floor. - L / R: which end of the opening the hinges are on. These are the two ends of the opening along the wall, not the 'stand outside and push' hand described above, so don't translate: look at the arc and tap the other one if the hinges land on the wrong side. - Open / Closed: Open shows the door ajar in 3D and its swing arc on the plan; Closed shows it shut with no arc, and Flow Check then ignores its swing. The arc updates live, and Smart Flow Check uses it as a no-furniture zone: anything inside it turns red. A French Door has In / Out, and both leaves open to the side you pick. A 2- or 4-panel French door has no L / R (its leaves are a mirrored pair); a 3-panel one has L / R for the side its single centre leaf hinges on. Switching a swing door to a French door (or back) with the type chip keeps In / Out, the hinge side and Open / Closed; see change a door type.

    In / Out and L / R in the door's settings. Tap one and watch the arc move on the plan.
  6. 6

    Closed doors on the plan

    Set a door to Closed when you want a clean drawing, for example a closet door that's normally shut. It's drawn as a line in the wall with no arc. Leave doors Open while you arrange furniture: a closed door has no arc, so Flow Check can't warn you about the swing.

    Closed: a line in the wall, no arc, and no swing check.

Tips

Walk through the open door in your head

Picture the door open. Where does it lie? Against which wall? Is the light switch where your hand reaches as you step in? Then switch to 3D and look from the doorway.

Small bathroom? Try out-swing or a pocket door

If a 30 in arc won't clear the toilet or vanity, swing the door out into the hall (if the hall is wide enough) or switch it to a pocket door with the type chip; both free the floor inside.

Two doors near each other

Doors in a short hall or a corner can hit each other. Keep at least 48 in plus the width of any door swinging into the space between two doors in a row (the ADA figure for doors in series, 404.2.6), or swing them so their arcs don't overlap.

Common confusions

Hand wrong because you imagined the wrong side

The hand is named from the side the door swings away from you. Imagining it from inside the room flips the answer; order from the plan, not from memory.

Believing every exterior door must swing out

That's a commercial rule (IBC, 50 or more occupants). Most house front doors swing in. What the residential code does require is a side-hinged exit door at least 32 in clear and 78 in high.

Planning furniture with the door set to Closed

A closed door has no arc, so Flow Check doesn't check the swing. Leave it Open while you lay out the room.

Leaving an inside door swinging into the wrong room

On an inside wall, In and Out are just the wall's two sides, and Flow Check tests the swing on the side the arc is drawn. If the bathroom door's arc opens into the hall on the plan, the tub inside isn't being checked against it. Look at the dashed arc, tap the other button if needed, and let Flow Check re-check.

Frequently asked questions

How do I tell if a door is left-hand or right-hand?

Stand on the side the door swings away from you. Hinges on your left = left-hand; hinges on your right = right-hand. The handle is always opposite the hinges.

Should doors swing inward or outward?

Inward, into the room they serve, is the convention for interior doors. Swing out when the room is too small for the arc, for some bathrooms (easier to reach someone who has fallen), or for weather on an exposed exterior door. In commercial rooms for 50 or more people the code requires doors to swing out in the direction of escape.

Does the building code say which way a front door must swing?

Not for a house. The IRC requires one egress door that is side-hinged, at least 32 in clear wide with the door open 90°, and 78 in clear high (R311.2), with a landing on each side at least 36 in deep. The swing direction is your choice.

How do I change the hinge side in RoomSketch3D?

Tap the door, then tap L or R in its settings. The door redraws with its hinges at the other end, and Smart Flow Check checks the new arc automatically. To flip which way it swings, tap In or Out. If you can't see an arc at all, the door is set to Closed: tap Open.

Which side should the light switch be on?

The latch (handle) side, inside the room, about 48 in up, so it's in reach as the door opens and not hidden behind it.

Sources

Start designing your room

Put this into practice in the floor plan maker: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android