Standard wall thickness
What thickness to draw for each wall type in residential floor plans, why (actual lumber and drywall sizes), and how RoomSketch3D handles it.
Walls in a floor plan have real thickness. Standard residential conventions:
Quick answer: draw interior walls about 4½ inches thick and wood-frame exterior walls about 6½ inches — RoomSketch3D's defaults. Use 6 inches or more for a plumbing wall and 8–12 inches for brick, block or a thick high-performance wall.
Why those numbers: a "2×4" stud is actually 1½ × 3½ inches and a "2×6" is 1½ × 5½ inches (dry, dressed sizes in the US softwood lumber standard, PS 20). Add ½-inch drywall on each face and a 2×4 wall is 4½ inches; a 2×6 wall with drywall is 6½ inches, before sheathing and siding.
In this guide
- 1
Interior walls
Typical: 4-5 inches (2×4 stud + drywall both sides). Plumbing wall: 6 inches (2×6 stud). Soundproofed: 6-8 inches.
Interior wall Build-up Thickness Standard partition 2×4 (3½ in) + ½ in drywall × 2 4½ in Plumbing wall 2×6 (5½ in) + ½ in drywall × 2 6½ in Sound wall Staggered or double studs 6–9 in Thin closet wall 2×3 or 2×4 flat + drywall 3–4 in Gypsum board for walls comes in 3/8, 1/2 and 5/8 inch thicknesses (the IRC's gypsum table lists all three); ½ inch is commonly used on house walls, and 5/8 inch where a fire-rated assembly calls for it.
Interior wall (selected) at 4.5" next to the 6.5" outside wall. - 2
Exterior walls
Standard 2×4 framing: 5-6 inches. Higher-performance 2×6 framing: 7-8 inches. Masonry/brick: 10-14 inches. Concrete: 8-12 inches. The extra over the stud depth is sheathing, insulation board and cladding. A plan that measures rooms to the inside face of walls (as most do) is not affected by the exterior thickness; the building's outer size is.
- 3
RoomSketch3D defaults
Default exterior: 6.5 inches. Default interior: 4.5 inches. Override in Settings → Measurements & Defaults → Floor plan defaults for new designs ("Exterior wall thickness" and "Interior wall thickness"; existing walls keep their saved thickness). To change one wall, tap it on the plan. An outside wall's panel has Thickness chips 4.5", 6.5", 8", 10" and 1', plus a box to type your own and a reset arrow; it also has Type (Wall / Railing / Open) and Is Load-bearing?.
Outside wall: Thickness 4.5" to 1', default 6.5". - 4
Interior wall thickness
An interior wall's panel shows its Length, Thickness (4.5 inches to start — tap it to type another value), Style (Full, Pony, Glass, Railing, Partition), Height and Is Load-bearing?. Set a plumbing wall to 6.5 inches so the plan shows the 2 inches it takes from the rooms beside it.
Interior wall: Thickness 4.5" by default. - 5
Where the outline sits: Exterior Wall Placement
Thickness has to go somewhere. Plan Settings → Walls → Exterior Wall Placement sets where the outline you drew sits relative to the wall body: Outside, Center or Inside. Outside: walls extrude outside the outline, so the sizes you typed are the inside clear sizes (what a tape measure reads in the room). Center: walls straddle the outline, so sizes are centerline to centerline. Inside: walls extrude inside the outline, so the sizes you typed are the building's overall footprint and the rooms are smaller.
Plan Settings → Walls → Exterior Wall Placement.
Tips
Measure rooms, not walls
Tape-measure each room wall to wall inside, then let the app's wall thickness add the rest. It's more accurate than trying to measure through a wall.
Common confusions
Drawing every wall the same thickness
A 6.5-inch interior wall everywhere steals about 2 inches from every room. Use 4.5 inches for ordinary partitions.
Frequently asked questions
What's the standard interior wall thickness?
4-5 inches for typical residential.
What's the standard exterior wall thickness?
6-8 inches for typical wood-frame residential.
How do I set wall thickness in RoomSketch3D?
Set exterior and interior defaults in Settings → Measurements & Defaults → Floor plan defaults for new plans, or select a wall and change its Thickness in its settings panel.
Why is a 2×4 wall 4½ inches, not 4?
A 2×4 is actually 3½ inches deep (US softwood lumber standard PS 20), plus ½-inch drywall on each side.
Sources
- U.S. DOC Voluntary Product Standard PS 20-25, American Softwood Lumber Standard — Table 3, nominal and minimum dressed sizes — Nominal 2×4 = 1½ × 3½ in dry; 2×6 = 1½ × 5½ in dry.
- 2021 International Residential Code — Table R702.3.5, gypsum board thickness — Lists 3/8, 1/2 and 5/8 in gypsum board; read on UpCodes.
Start designing your room
Put this into practice in the floor plan maker: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.
Open RoomSketch3DOne-time purchase · No subscription · Web, iOS & Android