Skip to main content

Wall utilities: outlets, switches, safes

Wall utilities — switches, outlets, safes — small wall fixtures with conventional symbols, mounting heights and code spacing rules.

6 min readUpdated 2026-11-17

Switches, outlets, and wall safes are small wall-mounted fixtures with conventions for placement and symbols.

Quick answer: along a wall, no point on the floor line may be more than 6 feet from an outlet (so outlets at most 12 feet apart); along a kitchen counter, no point more than 24 inches from one; in a bathroom, one within 36 inches of each basin. Switches go on the latch side of the door at a comfortable reach — and an accessible reach range tops out at 48 inches.

The example below is the 10 ft 6 in × 12 ft 6 in second bedroom of the Medium 2-Bedroom Apartment template: a switch beside the doorway, an outlet on each side of the bed, one on the side wall, and a wall safe on the side wall.

In this guide

  1. 1

    Light switches

    Mounting height: 48 inches to center above floor (standard); 44 inches for accessibility. Placement: next to the latch side of room doors, on the room-interior side. Types: single-pole, 3-way (two switches one fixture), dimmer, smart switch. In RoomSketch3D: switches aren't in the Build panel. In the Furnish catalog (Fixtures category) search switch and pick Light Switch (3D), Double Light Switch (3D) or Dimmer Switch (3D), then tap the wall; it goes in at 46 inches to its bottom edge; there is no separate smart-switch fixture — for the plan, the Symbols tab has Switch (Smart), Switch (Dimmer) and Switch (4-Way) symbols. Select a placed switch to change its kind from the drop-down or its Mount (the height of the bottom of the plate; 46 inches by default, about 48 inches to the centre). The 48 / 44-inch figures are common practice, not a code number for homes. For accessible design, the 2010 ADA Standards set the reach range for operable parts at 15 inches minimum and 48 inches maximum above the floor, for both forward and side reach (308.2.1, 308.3.1).

    Bedroom: switch by the doorway (S), outlets either side of the bed and on the left wall, safe on the left wall.
  2. 2

    Electric outlets

    Mounting height (general): 12-18 inches above floor for standard; 42-48 for kitchen counter outlets; 24-28 for bathroom. Placement (residential code): no point on any usable wall more than 6 feet from an outlet — outlet at least every 12 feet of wall. Kitchen counters: every 4 feet. Types: standard duplex, GFCI (bathrooms, kitchens, outdoor), USB-integrated, smart outlet. In RoomSketch3D: outlets aren't in the Build panel either. In the Furnish catalog (Fixtures category) search outlet and pick Duplex Outlet (3D), GFCI Outlet (3D) or USB + Outlet (3D), then tap the wall. There is no separate smart-outlet item. A placed outlet's Mount box sets its height (12 inches to the bottom of the plate by default; 42 inches for GFCI). Its Along wall boxes give the distance to the next wall or opening each way, and the padlock beside each one locks that distance, so the outlet stays the same distance from a corner or door frame when the wall changes (see electrical floor plan guide#lock distance). Several devices at one spot, such as a double outlet or a switch with an outlet below it, become one combination: drag one onto the other, or tap Add outlet / Add switch in its settings (see outlet and switch combinations). Stacked like that, each device's height from the floor is printed beside its symbol on the plan and on image and PDF exports.

  3. 3

    The spacing rules, with their sources

    RuleNumber2021 IRC (NEC)
    General wall spaceNo point along the floor line more than 6 ft from an outletE3901.2.1 (210.52(A)(1))
    What counts as wall spaceAny wall 2 ft or widerE3901.2.2
    Kitchen countertopEvery counter 12 in or wider; no point along the wall line more than 24 in from an outletE3901.4.1 (210.52(C)(1))
    BathroomAt least one outlet within 36 in of the outside edge of each basinE3901.6 (210.52(D))
    GFCI protectionBathrooms, garages, outdoors, crawl spaces, basements, kitchen countertops, within 6 ft of sinksE3902

    Worked example: a 12-ft wall with a door at one end needs an outlet near its middle; two outlets 12 ft apart cover the 6-ft rule exactly. Code minimums; local amendments vary, and an electrician has the final word.

    An outlet's card: Along wall distance to the next wall or opening each way (check the 6-ft rule), a padlock to lock each one, In / Out, kind and Mount.
  4. 4

    Wall safes

    Mounting height: 36-60 inches to bottom of safe. Behind a hanging picture is common. Standard sizes: 12-36 inches wide × 12-24 inches tall × 6-16 inches deep. Wall depth required: safe depth + 4 inches for installation. Standard 4-inch interior walls cannot accommodate most wall safes; need 6-inch walls minimum. In RoomSketch3D: in the Furnish catalog search wall safe and pick Wall Safe (16 inches wide), then tap the wall. Select it to set its Width, its position (the two Along wall boxes: distance to the nearest wall or opening each way), Height, Depth (how far it goes into the wall, limited by the wall's thickness) and Mount (the height of its bottom above the floor). A new wall safe is 16 in wide × 14 in tall, mounted at 4 ft.

    Wall Safe: Width, Along wall position, Height, Depth (D) and Mount.
  5. 5

    Placing them on a wall

    All three place the same way: pick the item in Furnish, then tap a wall (a picked item waits for a wall tap rather than dropping into the room). On an interior wall, a switch or outlet lands on the face you tapped from; pick In or Out in its settings card to move it to the other face. On a tablet or computer the card floats over the plan and can be dragged by its top row; on a phone it runs along the bottom. Drag it along the wall to move it. For a 2D electrical drawing with standard symbols (3-way and 4-way switches, smart switches, 240V outlets and more) use the Symbols tab instead; see electrical plan outlets switches symbols.

    A bedroom in 3D: the wall safe sits at 4 ft on the side wall.
  6. 6

    Bathroom: outlet beside the mirror

    In a bathroom, put the GFCI outlet within 36 inches of the basin and just clear of the mirror's edge, at counter-splash height (the example uses 42 inches to its bottom).

    GFCI outlet beside the vanity mirror.

Tips

Switch goes next to the door's latch side

As you walk through the open door, your hand naturally falls onto the switch.

Plan outlets around the furniture

Place the bed, sofa and desk first, then the outlets: one each side of the bed, one behind the TV console, one at the desk.

Frequently asked questions

How high should light switches be?

48 inches to center is standard residential. 44 inches for accessibility. The ADA reach range for operable parts is 15–48 inches above the floor.

How far apart should outlets be?

Maximum 12 feet between outlets along any usable wall — no point on the floor line more than 6 feet from one (2021 IRC E3901.2.1).

Can I mark switches and outlets in RoomSketch3D?

Yes, two ways. For switches and outlets you can see in 3D, search switch or outlet in the Furnish catalog and tap a wall. For a 2D electrical plan with standard symbols, open the Symbols tab (next to Indoor and Outdoor on the right, or the Symbols pill on a phone); it is always there, no setting needed. See electrical plan outlets switches symbols.

How do I show a switch with an outlet under it, or a double outlet?

Drag one device onto the other on the plan, or select one and tap Add outlet or Add switch. Pick Stacked to give each device its own Mount height (each height is then printed beside its symbol), or Side by side for a multi-gang frame. See outlet and switch combinations.

Can I fix an outlet at an exact distance from a corner or door?

Yes. Type the distance in its Along wall box, then tap the padlock beside it. A locked outlet keeps that distance when the wall changes and can't be dragged until you unlock it.

What heights are used in Germany?

DIN 18015-3 gives preferred heights of 105 cm (middle zone) and 30 cm (lower zone) above the finished floor for switches and sockets. Mount in RoomSketch3D is the bottom of the plate, so type about 101 cm and 26 cm. See electrical floor plan guide.

How many outlets does a kitchen counter need?

Every counter section 12 inches or wider needs one, and no point along the wall line may be more than 24 inches from an outlet — so about one every 4 feet (2021 IRC E3901.4.1).

Sources

Start designing your room

Put this into practice in the floor plan maker: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android