Accurate floor plan checklist
Before you export or share a floor plan, run through this checklist. Most common errors caught.
An 11-point check before you export or share. Catches the errors that cost the most to fix later.
Most expensive mistakes in a plan are small: a wall 3″ short, a door hinged on the wrong side, a ceiling height left at the default. Each looks fine on screen and only shows when furniture arrives or a contractor quotes. The checks below take about ten minutes and use tools already in the editor; each one says exactly where to look.
In this guide
- 1
1. Walls closed
Every room should be enclosed by walls forming a complete polygon. No gaps where two walls don't meet. RoomSketch3D auto-detects rooms — if a room isn't detected, the walls aren't closed. How to check: each detected room gets its own floor tint and a label with its size and area. A space with no tint and no label is not a room yet — look for a gap at a corner or an interior wall that stops short of the wall it should meet.
- 2
2. Wall lengths match reality
Spot-check at least three wall lengths against your physical measurements. Pay attention to walls with alcoves, columns, or chimney breasts. To fix one, tap the wall on the plan and type its length (see Set an exact wall length). With an outside wall's link on (how it starts), the wall at the end that moves comes along, so the outline stays closed; with the link turned off, a shorter length leaves a dashed gap at that end instead (tap the gap's + to fill it). The wall's panel also shows its Height (the room default unless you changed it) and Thickness — check both, because a 4½″ wall typed where there's really a 6½″ one shifts every room behind it by 2″.
Tap a wall: length on the plan, and Length, Height and Thickness in the panel below. - 3
3. Corners are square
Open View & Layers in the toolbar above the plan and turn on Show corner angles (in the Dimensions group). Every corner of the outline shows its angle, measured where the walls meet on the inside: square corners read 90° in green. The inside corner of an L-shaped plan reads 270°, which is correct. A corner like 88° or 92° usually means one wall length was typed or traced slightly wrong; retype the lengths, or use All 90° in Plan Settings → Layout → Outline Editor if every corner should be square.
View & Layers → Show corner angles: all four corners read 90°. - 4
4. Doors in the right place
Each door should be on a real wall in the right position. Check swing direction and hinge side — left vs right hand matters. How to check: tap the door. Its panel shows the Width (2′ 6″, 2′ 8″, 3′, 3′ 6″ or Other), the Height (6′ 8″ is standard), the two Along wall distances (boxes marked ← and →, or ↑ and ↓ on a wall that runs up and down the plan), In / Out (which side it swings to) and L / R (hinge side). Compare the Along wall distance with your tape: the door's position matters as much as its width. See door swing and hinge side.
Door settings: width, height, Along wall, In / Out and L / R. - 5
5. Window positions
Each window on the wall it's actually on, sized to the real window, positioned where the real window is (not centered if it's actually off-center). Tap each window and check its distance from the corner as well as its width; then glance at Elevation views to check its sill and head heights against what you measured. A window seat, desk or radiator under a window depends on the sill height.
- 6
6. Ceiling heights
Set when you create the design (8 feet unless you picked another). If your home has 9 or 10 foot ceilings, change it in Plan Settings → Ceiling. For sloped or vaulted ceilings, add a Vaulted Ceiling from the Structural tools. Ceiling height decides what fits (tall bookcases, bunk beds, a ceiling fan's clearance) and how the 3D view looks. For reference, the International Residential Code's minimum for habitable rooms is 7 feet, and 6′ 8″ for bathrooms and laundry rooms (IRC R305.1); most new homes are 8–9 feet. See ceiling height standards.
Plan Settings → Ceiling: the ceiling height for the floor (9′ here). - 7
7. Stairs (if any)
Rise matches floor-to-floor height. Shape (straight/L/U) matches the real staircase. Direction (up/down) correct. A quick sanity check: under the International Residential Code a riser is at most 7¾″ and a tread at least 10″ (IRC R311.7.5.1 and R311.7.5.2), so a 9-foot floor-to-floor rise (108″ plus the floor structure) needs at least 14 risers. If your plan's stair is much shorter than your real one, the step count or rise is off. See riser and tread standards.
- 8
8. Smart Flow Check passes
If Smart Flow Check shows red warnings, address them. At least understand them — sometimes warnings are intentional (e.g., a rug you meant to put under the sofa). The pill at the top left reads Flow check OK in green when nothing is wrong, or Flow check with a count when something is. Tap it to see each issue in plain words — here, Accent Chair blocks door — Move it away from the door swing — with the piece outlined in red on the plan. See what is smart flow check.
Flow Check: the chair inside the front door's swing is outlined red, and the panel says what to fix. - 9
9. Furniture fits in 3D walkthrough
Switch to 3D and walk through the room. If anything feels wrong — head clearance, doorway angles, sightlines — it probably is. In walk mode, use the keys (W A S D) or the joystick to walk the path you'll walk every day: front door to kitchen, bed to bathroom. See walk mode keyboard and mobile joystick.
- 10
10. Room labels are reasonable
Auto-detected room names should match the use you intend. Rename if needed. Tap a room's label and its room card opens: type a new Name there (clear the box to go back to the automatic name), and read the room's clear size and floor area under it. To see every room's size and area on the plan at once, open View & Layers, tap Label style under Show room labels and pick Name + size + area. Check the size against your tape — it's the clear space between wall faces.
Tap a label: the room card, to rename the room and check its clear size and area. - 11
11. Units are correct
If you're sharing with someone in the US, make sure the plan is in feet/inches. With someone in Europe — meters/centimeters. Check Settings → Measurements & Defaults (from your account menu at the top right). Measurement Units switches between ft/in and m/cm; Measurement format chooses whether lengths read 7′ 6″ or 90″. Exports use the same units, so set them before you export.
Settings → Measurements & Defaults: units and format.
Tips
Check in this order
Walls and corners first, then doors and windows, then heights, then furniture. Fixing a wall length after furnishing moves things you've already placed.
Export a test PDF
Before you send a plan, export it once and look at it the way the recipient will: are the dimensions legible, the room names right, the units the ones they expect?
Common confusions
Leaving the default ceiling height
A plan created at 8′ in a home with 9′ ceilings gives wrong elevations and a squat 3D view. Set the real height in Plan Settings → Ceiling.
Fixing the wrong wall
When opposite walls disagree, re-measure before typing: the wrong number is often the one you trust.
Frequently asked questions
How accurate should a floor plan be?
For furniture planning, within about ½″ per wall. For ordering built-ins, cabinets or flooring, measure the specific spot again to ⅛″ and leave the installer's recommended gap.
Why does a corner show 89° or 91°?
One of the walls meeting there is slightly off in length or position, usually from a typing or tracing slip. Retype the lengths, or use All 90° in the Outline Editor if the real room is square.
Where do I change the units?
In Settings → Measurements & Defaults, from your account menu at the top right. Choose ft/in or m/cm, and 7′ 6″ or 90″ format.
Sources
- International Residential Code (IRC) 2021, R305.1 — minimum ceiling height (City of Boise Planning & Development Services handout #434) — 7 ft for habitable rooms and hallways, 6 ft 8 in for bathrooms, toilet rooms and laundry rooms. Local codes vary — check with your building department.
- International Residential Code (IRC) 2021, R311.7.5 — stair treads and risers (City of Boise handout #437) — Riser not more than 7¾ in, tread not less than 10 in.
Start designing your room
Draw it, furnish it, walk through it in 3D — on web, iOS, and Android.
Open RoomSketch3DOne-time purchase · No subscription · Web, iOS & Android