Balcony dimensions
Standard residential balcony dimensions, by use case — plus the guard height, opening and load rules that apply to every balcony.
Standard balcony sizes are determined by intended use — Juliet, sitting, dining, outdoor-room. Local code typically requires railings at 36-42 inches high; structural requirements limit projection.
Quick answer: a standard balcony is 36–72 inches (91–183 cm) deep and 60–84 inches (152–213 cm) wide — 36 inches fits two chairs, 60+ inches fits a small table with seating. The railing is 36–42 inches (91–107 cm) high.
The example below is a 10 × 5 ft balcony off a bedroom's French doors, furnished with a 42-inch bistro table and two chairs — about the smallest size where a table and two chairs fit without crowding.
In this guide
- 1
Depths by use
Juliet (decorative, no standing): 12-18 inches. Sitting (2 chairs): 36-60 inches. Dining (small table): 60-96 inches. Outdoor room (multiple zones): 72-144 inches.
Use Depth What fits Juliet 12–18 in Nothing — a rail at the door Sitting 36–60 in Two chairs side by side Dining 60–96 in 30–42 in table + 2–4 chairs Outdoor room 72–144 in Seating group, lounger, table Worked example: a 42-inch round table plus a 30-inch-deep chair on each side needs about 102 inches of length; that's why the balcony below is 10 ft long and 5 ft deep. These are comfort guidelines, not code.
10' × 5' balcony with a bistro set: the plan labels its length and depth. - 2
Widths
Minimum (single-room access): 48 inches (matches a French door pair). Standard bedroom balcony: 60-84 inches. Master suite balcony: 96-144 inches. Full wall balcony: 144-240 inches.
- 3
Railings
Height: 36-42 inches. Baluster spacing: max 4 inches between balusters. The code numbers behind those ranges: - When a guard is required: a walking surface more than 30 inches above the floor or grade below, measured within 36 inches horizontally of its edge (2021 IRC R312.1.1). - Height: at least 36 inches for one- and two-family homes (IRC R312.1.2). The International Building Code asks for 42 inches (IBC 1015.3), with an exception that keeps 36 inches inside dwelling units of Group R-3 and of Group R-2 buildings up to three stories. - Openings: a 4-inch sphere must not pass through the guard (IRC R312.1.3), which is where the familiar "4-inch baluster spacing" comes from. Code minimums; local codes vary — check with your building department.
- 4
Structural projection limits
Cantilevered: up to ~6 feet projection without supplemental columns. Column-supported: up to 12 feet+ with proper structure. These are rules of thumb; the real limit depends on the joists or slab, so an engineer or the span tables decide. For the loads, the 2021 IRC sets 40 psf live load for exterior balconies and decks, and 200 lb concentrated load for guards (Table R301.5).
- 5
Set the size in RoomSketch3D
In the left panel's Structural section tap Balcony / Patio, choose the shape, then tap an outside wall. A new rectangular balcony starts 8 ft long (shorter on a short wall) and 4 ft deep, with a Spindle railing at 3 ft 6 in. Select it and its settings show (in a floating card on a tablet or computer, along the bottom on a phone): Length (with Stretch across wall), Depth, Covered, Railing (Open, Spindle, Pony Wall, Glass, Horizontal Slat, Cable, Wrought Iron, Picket), Rail height (presets 3', 3' 6", 4', or type your own) and Floor (Composite, Wood, Tile, Concrete). Choose Open for a ground-level patio with no railing. Length goes from 2 ft up to the wall's length. A regular balcony or patio can also run past an outside corner of the house, up to 20 ft beyond it, when there's open ground there: type a longer Length or drag its end. It stops at an inside corner or anything in the way. That's how to draw a long deck or a porch that carries on past the house; see How to add balconies.
Length, Depth, Railing style, Rail height and Floor for the selected balcony. - 6
Check it in 3D
The 3D view draws the balcony floor, railing and any furniture you place on it. Look from outside to judge the proportions against the facade.
The balcony from outside: spindle railing at 3' 6". - 7
And from inside
From inside the bedroom, check that the doors, the bed and the balcony furniture line up — the table should be visible through the doors, not blocking them.
Looking out through the French doors.
Tips
Size from the furniture, not the facade
Place the actual table and chairs on the balcony first, then set Length and Depth so there's room to pull a chair out (about 24 inches behind each one).
Frequently asked questions
What is the standard size of a balcony?
36–72 inches (91–183 cm) deep and 60–84 inches (152–213 cm) wide for a typical bedroom or sitting balcony. Larger master-suite balconies run 96–144 inches wide.
What is the minimum balcony size?
About 48 inches (122 cm) wide for single-room access (matches a French door pair). A sitting balcony for two chairs needs 36 inches (91 cm) deep; a decorative Juliet balcony (no standing) is only 12–18 inches deep.
What's the standard balcony depth?
36-72 inches. 36 fits two chairs; 60+ fits a small table.
How tall does a balcony railing need to be?
36 inches minimum for one- and two-family homes (2021 IRC R312.1.2). The IBC's general rule is 42 inches (1015.3), with a 36-inch exception inside R-3 and low-rise R-2 dwelling units. Check local code.
Does RoomSketch3D draw the railing for me?
Yes — the balcony railing renders automatically at the size you place, and you can choose its style and height in the balcony's settings bar.
Sources
- 2021 International Residential Code — R312.1.1–R312.1.3 guards; Table R301.5 live loads — Unamended 2021 IRC as adopted by Colorado, read on UpCodes.
- 2021 International Building Code — 1015.3 guard height — Applies to buildings under the IBC; local codes vary.
Start designing your room
Put this into practice in the floor plan maker: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.
Open RoomSketch3DOne-time purchase · No subscription · Web, iOS & Android