Skip to main content

Door rough opening sizes

The framed hole in the wall is bigger than the door: about 2 in wider and 2½ in taller for a prehung hinged door. Here's the chart, where the allowance goes, and what to draw on your plan.

4 min readUpdated 2026-11-16

The rough opening (RO) is the framed hole in the wall, before the door frame goes in. It's larger than the door so the frame (jambs), shims and small adjustments fit. The usual rule for a prehung hinged door: RO width = door width + 2 in; RO height = door height + 2½ in (80 in door → 82½ in RO).

Quick answers (80 in tall hinged doors): 28 in door → RO 30 × 82½ in. 30 in → 32 × 82½. 32 in → 34 × 82½. 36 in → 38 × 82½. Door makers' own charts are close to this: Masonite lists 34½ in and 38½ in as common exterior rough-opening widths and 82½ in as a common height.

Treat these as planning numbers. The exact rough opening is printed on the installation sheet of the door you buy, and it varies with the frame (wood or steel), the jamb and the threshold.

In this guide

  1. 1

    Where the extra 2 inches go

    Across the width: each side jamb is about ¾ in thick, plus about ¼ in of shim space each side: ¾ + ¼ + ¾ + ¼ ≈ 2 in. Up top: the head jamb (¾ in), shim space, and a ½–1 in gap under the door for the floor finish and air: about 2½ in. The trim (casing) then covers the joint, overlapping the wall by another 2½–3½ in each side. So a 32 in door takes about 34 in of framing and about 40 in of finished wall face, casing to casing. Remember that when you need room beside a door for a cabinet or a light switch.

    The plan shows the door's own width and the wall left on each side (here 2′ 6.75″). The rough opening takes about 1″ more of that wall on each side.
  2. 2

    Interior hinged doors

    24 in door: RO 26 × 82½ in. 28: 30 × 82½. 30: 32 × 82½. 32: 34 × 82½. 36: 38 × 82½. For a door taller than 80 in, add 2½ in to its height the same way (96 in door → 98½ in RO).

  3. 3

    Exterior hinged doors

    32 in: RO about 34–34½ × 82½ in. 36: about 38–38½ × 82½ in. Exterior units carry a sill and threshold, so check the maker's sheet: some need an extra ½–1 in in height, and the RO must be level and square for the weatherstrip to seal.

  4. 4

    French doors

    60 in pair: RO about 62 × 82½ in. 64: 66 × 82½. 72: 74 × 82½. Exterior French units with sidelites have their own charts; the unit width (not the leaf width) sets the RO.

  5. 5

    Sliding glass doors

    Patio sliders come as a complete frame, so they're ordered by unit size, and the RO is only a little larger than the unit, typically about ½ in each way (a 72 × 80 in unit takes about a 72½ × 80½ in RO). Always use the maker's chart: slider unit sizes are often a fraction under the nominal size.

  6. 6

    Pocket doors

    A pocket door needs room for the door and the pocket beside it, so the RO is roughly twice the door width plus about 1 in, and about 4 in taller than the door for the track. A 32 in pocket door takes about a 65 × 84½ in RO with a typical frame kit. The kit's instructions give the exact number, and the whole RO must be free of pipes, wiring and ducts.

  7. 7

    In RoomSketch3D

    RoomSketch3D draws and dimensions the door, not the rough opening: a 32 in door is a 32 in gap in the wall, and the two Along wall boxes in its settings (← / →, or ↑ / ↓ on an up-and-down wall) measure from the door's edge to the nearest wall or opening. That's what you want on a layout plan. Give your builder the door size; they frame the opening to suit the door they install. If a tight spot matters (a door beside a corner, a cabinet beside a door), leave about 1 in more on each side for the frame and another 3 in for the casing. In 3D, the door is shown in its frame, so you can see how much wall is left either side.

    Set the door's real size (width and height). The rough opening is the builder's job.
  8. 8

    Check it in 3D

    Switch to 3D and look at the doorway: the frame sits in the wall and the casing shows how much wall is left beside it. If the door is near a corner, check there's still a few inches of wall for the casing.

    In 3D the door sits in its frame in the wall.

Tips

Buy the door first, then frame

Rough-opening sizes vary a little by maker. If you can, pick the exact door and frame to its installation sheet.

Leave wall beside the door

Door near a corner? You need the RO allowance (about 1 in) plus the casing (2½–3½ in) on that side. Less than about 4 in of wall from the door's edge to the corner and the casing won't fit.

Common confusions

Framing the hole to the door size

A 32 in hole won't take a 32 in prehung door: the jambs and shims need about 2 in more.

Forgetting the floor

The 2½ in height allowance assumes the RO is measured from the finished floor level the door will sit on. Thick tile or hardwood added later eats into the gap under the door.

Frequently asked questions

What is a rough opening for a door?

The framed hole in the wall before the door frame is installed, sized larger than the door to leave room for the jambs, shims and adjustment.

What is the rough opening for a 32 inch door?

34 in wide × 82½ in tall for a standard 32 × 80 in prehung hinged door (door width + 2 in, height + 2½ in). Check the door's install sheet for the exact figure.

What is the rough opening for a 36 inch door?

38 in wide × 82½ in tall for a 36 × 80 in prehung door; exterior units are often listed at 38½ in wide.

What is the rough opening for a 30 inch door?

32 in wide × 82½ in tall for a 30 × 80 in prehung door.

How much larger is the rough opening than the door?

About 2 in wider and 2½ in taller for most prehung hinged doors. Sliders: about ½ in. Pocket doors: about twice the door width plus 1 in.

Do I specify the rough opening in RoomSketch3D?

No. RoomSketch3D uses the door's actual width and height. The rough opening is a framing detail your builder works out from the door they install.

Sources

Start designing your room

Put this into practice in the floor plan maker: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android