Skip to main content

Cased vs uncased openings

Cased = trimmed like a door frame. Uncased = drywall wrapped, no trim. The choice signals traditional vs modern.

4 min readUpdated 2026-11-16

A doorless opening can be finished two ways. The choice is one of the clearest signals of architectural style.

Quick answer: match the doors. If the doors in the house have casing (trim) around them, case the openings too; if the doors have minimal or no trim, wrap the openings in drywall. The opening's size and position are the same either way — only the edge finish changes.

On a floor plan the two look identical: a gap in the wall. That's how RoomSketch3D draws it too, so you can plan the size and the walkway now and decide the finish with your builder.

In this guide

  1. 1

    Cased opening

    Trim around the opening — jambs on sides, head casing on top. Same trim profile as a door frame, just without the door. Reads: traditional, classic, formal. Matches Colonial, Victorian, Craftsman. Cost: moderate — same trim and labor as a door frame. Casing adds width on the wall face: a 3½-inch casing on both sides of a 48-inch opening takes about 55 inches of wall. Leave room for it next to switches, corners and furniture.

  2. 2

    Uncased opening

    Drywall returned with no trim. Sometimes with a small bullnose corner bead. Reads: contemporary, modernist, minimalist. Cost: lower — no trim materials, but careful drywall finishing required. Without trim to hide joints, the framing has to be straight and the corners crisp, so the finishing labour matters more than with a cased opening.

  3. 3

    On the plan: the same gap

    In RoomSketch3D, tap the Opening tile in the left panel's Doors & Windows section, then tap a wall (an outside wall or an interior wall). The opening draws as a gap with no door leaf and no swing arc — exactly how a cased or uncased opening appears on construction drawings. Here it's a 4-ft opening in the wall between two rooms.

    A 4' opening in an interior wall: a gap, no door leaf, no swing.
  4. 4

    Its settings

    Select the opening to set Width (presets 3', 4', 5', 6' or Other), the two Along wall distances (↑ ↓, or ← → on a wall that runs across the plan) to position it, Doorway or Pass-through, and Height. A doorway starts 6 ft 8 in tall, a standard door height; raise it for a taller, more open look. There's no casing setting — the finish is your call with the builder.

    Width, position, Doorway / Pass-through and Height.
  5. 5

    In 3D: plain edges

    In 3D the opening renders with plain, square wall edges — effectively the uncased look. If you're planning a cased opening, picture an extra few inches of trim on each face around what you see.

    The opening in 3D: square, trimless edges.
  6. 6

    Pass-throughs follow the same rule

    A kitchen pass-through (serving hatch) is cased or uncased by the same logic. Select the opening and tap Pass-through: it lifts to a 36-inch sill (counter height) and 36 inches tall, and the wall stays solid below it.

    Pass-through: a raised opening, wall below.
  7. 7

    How to choose

    Match the rest of the trim. Doors with wide trim → openings cased. Flat-trimmed contemporary doors → openings uncased. Mixing reads wrong.

    CasedUncased
    EdgeJamb + head casingDrywall return, corner bead
    StyleTraditional, Craftsman, ColonialModern, minimalist
    CostTrim + carpentryLess material, more finishing care
    Hides imperfect framingYesNo

    These are design conventions, not code. For width, a walkway opening of 36 inches or more keeps an accessible route clear (the 2010 ADA Standards set 36 inches for an accessible route, 403.5.1); most interior openings are 36–72 inches.

Tips

Keep 36 inches clear in front of a doorway opening

Flow Check warns when furniture sits within 36 inches in front of an opening. In an interior wall it checks both sides, since you walk through from either room. A pass-through isn't a walkway, so it isn't checked.

Frequently asked questions

What's the difference between cased and uncased openings?

Cased = surrounded by trim (jambs and head casing) like a door frame. Uncased = drywall returned with no trim.

Which is more modern?

Uncased. Lack of trim reads contemporary; cased reads traditional.

How do I add an opening in RoomSketch3D?

Use the Opening tile and tap a wall — a doorless passage with no swing arc. Set the width; there is no leaf to keep clear.

Can RoomSketch3D show casing around an opening?

No. Openings render with plain edges in 3D and there's no casing setting. Plan the size and height; choose the finish with your builder.

Sources

Start designing your room

Put this into practice in the floor plan maker: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android